Wiley.com
Print this page Share

Advanced Processing and Manufacturing Technologies for Structural and Multifunctional Materials, Volume 28, Issue 7

Tatsuki Ohji (Editor), Mrityunjay Singh (Editor), Jonathan Salem (Volume Editor), Dongming Zhu (Volume Editor)
ISBN: 978-0-470-19638-0
204 pages
November 2007
Advanced Processing and Manufacturing Technologies for Structural and Multifunctional Materials, Volume 28, Issue 7 (0470196386) cover image

Description

Papers from The American Ceramic Society's 31st International Conference on Advanced Ceramics and Composites, held in Daytona Beach, Florida, January 21-26, 2007. Topics include processing and manufacturing technologies for a wide variety of non-oxide and oxide based structural ceramics, particulate and fiber reinforced composites, and multifunctional materials. Presents advances in various processing and manufacturing technologies for fine scale MLCCs, transparent ceramics, electronic ceramics, solid oxide fuel cells, and armor ceramics.
See More

Table of Contents

Preface ix

Introduction xi

Slurry Characterization by Stress Relaxation Test for Tape Casting Process 1
Takamasa Mori, Tomofumi Yamada, Tatsuya Tanaka, and Junichiro Tsubaki

Preparation of Stable Nano-Sized Al203 Slurries Using Wet-Jet Milling 11
Toshihiro Isobe, Yuji Hotta, Kimiyasu Sato, and Koji Watari

Design of Mold Materials for Encapsulating Semiconductors Using Epoxy Compounds 19
Satoshi Kitaoka, Naoki Kawashima, Keiji Maeda, Takaki Kuno, and Yoshinori Noguchi

Evaluation of an Environmentally Friendly Plasticizer for Polyvinyl Butyral for Use in Tape Casting 27
Richard E. Mistier, Ernest Bianchi, Bruce Wade, and Jeffrey Hurlbut

Mutual Linkage of Particles in Ceramic Green Bodies through Reactive Organic Binders 35
Kimiyasu Sato, Miyuki Kawai, Yuji Hotta, Takaaki Nagaoka, Koji Watari, and Cihangir Duran

Drying Dinetics of Slip Cast Body by Microwave Heating 47
Takashi Shirai, Masaki Yasuoka, Yoshiaki Kinemuchi, Yuji Hotta, and Koji Watari

Microwave Sintering Techniques—More than Just a Different Way of Heating? 55
G. Link, S. Miksch, M. Thumm, and S. Takayama

The Effect of the Electrical Properties on the Pulsed Electric Current Sintering Behavior of Zr02 Based Ceramic Composites 67
K. Vanmeensel, B. Neirinck, S. Huang, S. Salehi, O. Van der Biest, and J. Vleugels

Smart Processing Development on 3D Ceramic Structures for Terahertz Wave Applications 79
Y. Miyamoto, W. Chen, H. Kanaoka, and S. Kirihara

Fabrication of New Dielectric Fractal Structures and Localization of Electromagnetic Wave 91
Y. Nakahata, S. Kirihara, and Y. Miyamoto

Micro-Fabrication and Terahertz Wave Properties of Alumina Photonic Crystals with Diamond Structure 99
H. Kanaoka, S. Kirihara, and Y. Miyamoto

Texture Development of Bi4Ti3012 Thick Film Promoted by Anisotropie Shrinkage 105
Y. Kinemuchi, P.H. Xiang, H. Kaga, and K. Watari

Anisotropie Properties of Al Doped ZnO Ceramics Fabricated by the High Magnetic Field 113
Hisashi Kaga, Yoshiaki Kinemuchi, Koji Watari, Hiromi Nakano, Satoshi Tanaka, Atsushi Makiya, Zenji Kato, and Keizo Uematsu

Porous Anatase Titanium Dioxide Films Prepared in Aqueous Solution 121
Yoshitake Masuda, Tatsuo Kimura, Kazumi Kato, and Tatsuki Ohji

Preparation of Micro/Mesoporous Si-C-0 Ceramic Derived from Preceramic Route 133
Manabu Fukushima, You Zhou, Yu-ichi Yoshizawa, Masayuki Nakata, and Kiyoshi Hirao

Porous Alumina Ceramics by Novel Gelate-Freezing Method 139
Masayuki Nakata, Manabu Fukushima, and Yu-ichi Yoshizawa

New Production Approaches for Large and Very Complex Shapes of Silicon Nitride and Silicon Carbide Ceramics 145
Karl E. Berroth

Fabrication and Mechanical Properties of Porous Silicon Nitride Materials 155
Tatsuki Ohji

Application of Taguchi Method in the Optimization of Process Parameters for Conicity of Holes in Ultrasonic Drilling of Engineering Ceramics 167
R.C.S. Mehta, R.S. Jadoun, Pradeep Kumar, and B.K. Mishra

Simulation of Material Removal Rate in Ultrasonic Drilling Process Using Finite Element Analysis and Taguchi Method 179
R.S. Jadoun, B.K. Mishra, Pradeep Kumar, and R.C.S. Mehta

Author Index 195

See More

Buy Both and Save 25%!

+

Advanced Processing and Manufacturing Technologies for Structural and Multifunctional Materials, Volume 28, Issue 7 (US $128.00)

-and- 72nd Conference on Glass Problems: A Collection of Papers Presented at the 72nd Conference on Glass Problems, The Ohio State University, Columbus, Ohio, October 18-19, 2011, Volume 33, Issue 1 (US $87.95)

Total List Price: US $215.95
Discounted Price: US $161.96 (Save: US $53.99)

Buy Both
Cannot be combined with any other offers. Learn more.

Related Titles

Back to Top