 AutoCAD 2004 Bible
ISBN: 978-0-7645-3992-3
Paperback
1315 pages
June 2003
This title is out-of-print and not currently available for purchase from this site.
|
Do you think you've discovered an error in this book? Please check the list of errata below to see if we've already addressed the error. If not, please submit the error via our Errata Form. We will attempt to verify your error; if you're right, we will post a correction below.
| Chapter | Page | Details | Date | Print Run |
|---|---|---|---|---|
| 79 | Missing text in Step 15 At the end of 4th line of instructions ending “Figure 4-24.” add “(If you turned off OSNAP in Step 13, turn it on again.)” |
8/23/04 | ||
| 83 | Error in Step 11 Should be “…Midpoint: <270° Midpoint: <180°) and click.” |
8/23/04 | ||
| 94 | Text on CD-ROM icon On the CD-ROM icon: end should read "AutoCAD 2004 Bible CD-ROM." |
8/23/04 | ||
| 101 | Text on CD-ROM icon On the CD-ROM icon: end should read "AutoCAD 2004 Bible CD-ROM." |
8/23/04 | ||
| 104 | Missing level 1 head Above the text "There are two wizards…" add a new level 1 heading, "Using the Setup Wizards." |
8/23/04 | ||
| 110 | Errors in Steps 6 & 13 Step 6, should be “Type @.7341<129@@e.” Step 13, should be “Type @.8071<270@@e…” |
8/23/04 | ||
| 113 | Errors in Steps 4, 5, 6 & 7 Step 4, 2nd sentence, should be “…prompt, type @2’1”,1’9”@@e.” Step 5, 4th sentence, should be “…prompt, type @2,2…” Step 6, should be “…type @1’9”,1’3”@@e.” Step 7, should be “…type @11,2@@e.” |
8/23/04 | ||
| 114 | Error in Step 8 Step 8, 3rd sentence, should be “…prompt, type @1,-5@@e. |
8/23/04 | ||
| 161 | Error in Steps 5 & 6 Step 5, should be “Click the bottom-right viewport.” Step 6 should be “Click the bottom-left viewport.” |
8/23/04 | ||
| 169 | Error in Step 7 Step 7, 10th line of instructions, should be “Move the cursor in the 180° direction. |
8/23/04 | ||
| 171 | Error in tip Tip, 1st sentence, should be “…type plan (to start the PLAN command)…” |
8/23/04 | ||
| 173 | Error in Step 12 Step 12, 2nd sentence, should be “Start the line at 8.2272,2.25…” |
8/23/04 | ||
| 215 | Error in Step 13 Step 13, 3rd sentence, should be "…and check your settings." |
8/23/04 | ||
| 234 | Error in tip Tip, 2nd sentence, should be “Use the Break at Point button …” |
8/23/04 | ||
| 254 | Error in last paragraph Last sentence, should be "…palette has too many rows…" |
8/23/04 | ||
| 319 | Error in Step 5 Step 5, 3rd sentence should be “Look at the total editing time to see the total time the drawing has been worked on.” |
8/23/04 | ||
| 344 | Error on bottom of page On the CD-ROM, should be "…with DTEXT, 13-a.dwg, is in…" |
8/23/04 | ||
| 346 | Error in last bullet Should be "Only the TEXT command works …." |
8/23/04 | ||
| 349 | Error in 2nd sentence "To use JUSTIFYTEXT, choose modify…" |
8/23/04 | ||
| 411 | Error in Step 4 3rd line should be "…to dimension: Pick the line at @@4." |
8/23/04 | ||
| 417 | Error in heading Should read "Using the Properties palette to edit dimensions" |
8/23/04 | ||
| 449 | Error in Step 10 The numbers 1 and 2 should be in black circles, since they refer to circles in figure 15-28. |
8/23/04 | ||
| 458 | Error in Step 6 3rd sentence: should be “… choose the intersection at @@3. |
8/23/04 | ||
| 471 | Error in Step 8 2nd sentence, should be “…@-5/16, 5/16@@e.” |
8/23/04 | ||
| 511 | Error in figure 16-43 The captions on the bottom row are all the same, Instead they should read, from the left: "Closed tee", "Open tee", and "Merged tee". |
8/23/04 | ||
| 603 | Error in Step 9 End of first line, put full word “armchair” on 2nd line -- don’t hyphenate. (It's text to type in and a reader got confused, typing in the hyphen between arm and chair.) |
8/23/04 | ||
| 607 | Error in 1st paragraph End of 1st para, should be "…shown in Figure 18-24." |
8/23/04 | ||
| 610 | Error in Step 3 3rd sentence, should be “In the Value text box of the Enhanced Attribute Editor…” |
8/23/04 | ||
| 611 | Errors in Step 6 Add a new sentence after 1st sentence, “Press Enter to end selection.” Current 2nd sentence should read, “The attributes reappear, but without their values.” |
8/23/04 | ||
| 628 | Error in Figure 19-7 Move callout 1 so that the arrow is inside the blank rectangle that it's near; it needs to go a little further down. |
8/23/04 | ||
| 629 | Errors in Steps 9 & 10 Step 9, 2nd sentence, delete “(transfer)” Step 10, line 4 of instructions, delete “$0$STANDARD, “ |
8/23/04 | ||
| 650 | Error in Step 2 Should be "Choose dbConnect in the…" |
8/23/04 | ||
| 667 | Error in tip Should be “…prompt) and”; in other words, delete the comma after “prompt” and add a close paren. |
8/23/04 | ||
| 712 | Errors in Step 9 & Figure 21-18 Step 9, 3rd sentence, should be “…Figure 21-17…” Fig 21-18, arrow #3 needs to point to the right of the intersection it points to now. |
8/23/04 | ||
| 771 | Error in Step 10 Step 10, 2nd to last line of instructions, 9 in a circle should be 2 in a circle. |
8/23/04 | ||
| 841 | Error in Step 7 Step 7, 9th line of instructions, change “Step 3” to “Step 4”. |
8/23/04 | ||
| 891 | Error in Step 9 3rd to last sentence, should be "Change the Bitmap Blend to .30." |
8/23/04 | ||
| 892 | Error on text about CD-ROM On the CD-ROM, should be “…ab25-b.dwg…” |
8/23/04 | ||
| 923 | Error in Step 3 2nd sentence, should be "…more than one standards file with the drawing." |
8/23/04 | ||
| 932 | Error in Step 14 Should be “Choose ab26-e.dws…” |
8/23/04 | ||
| 1003 | Error in Step 1 2nd sentence should be "…the file to open it…" |
8/23/04 | ||
| 1023 | Error in Step 1 Delete "from the AutoCAD 2004\Support folder" |
8/23/04 | ||
| 1024 | Error in Step 9 Should be "…and drag Hide to the toolbar." |
8/23/04 | ||
| 1035 | Error in Sidebar 2nd to last para, 1st line, but a menu arrow between "Programs" and "Accessories". |
8/23/04 | ||
| 1039 | Error in tip 3rd sentence, should be "Drag the top border of the command line area downward to reduce the number of lines of text on the command line to 1." |
8/23/04 | ||
| 1090 | Error in Step 4 Monofont text, the 2nd & 3rd lines need to be on one line. They fit in previous edition. There needs to be a space between "select" and "\_move". |
8/23/04 | ||
| 1105 | Error in 2nd sentence Should read "The TABLET2 section starts this way:" |
8/23/04 | ||
| 1111 | Errors in Steps 9 & 13 Step 9, 1st line, add space between "on" and "your". Step 13, 2nd sentence, should read: "Choose View@@>3D Views@@>SE Isometric View." |
8/23/04 | ||
| 1120 | Error in 1st line Should be "…to load .fas, …" |
8/23/04 | ||
| 1140 | Error in Figure 35-1 Remove border |
8/23/04 | ||
| 1145 | Error in Step 3 Apostrophe in bold text should be straight, not curly |
8/23/04 | ||
| 1224 | Error in new feature icon Should be "…\Software\AutoCAD…" |
8/23/04 | ||
| 27 | Drawings for Chapter 27 missing from CD-ROM The drawings are available on the downloads page. They are titled ab27-a.dwg, ab27-b.dwg and ab27-c.dwg. |
8/23/04 |
Share This
