 CCIP: MPLS Study Guide: Exam 640-910 (Implementing Cisco MPLS)
ISBN: 978-0-7821-4096-5
Hardcover
466 pages
August 2002
This title is out-of-print and not currently available for purchase from this site.
Other Available Formats: Adobe E-Book
|
Do you think you've discovered an error in this book? Please check the list of errata below to see if we've already addressed the error. If not, please submit the error via our Errata Form. We will attempt to verify your error; if you're right, we will post a correction below.
| Chapter | Page | Details | Date | Print Run |
|---|---|---|---|---|
| Combined Errata Page 0CD EdgeTest, Chapter 2 see detailed description
The answer should read:
Page 13
replace the output for PE1 to: 192.168.1.21 <
Page 16
Paragraph under FIGURE 1.9, should read: "Now let's now see what happens... loopack address of P2."
Page 18
2nd to last line, "In Figure 1.8" should read "In Figure 1.11"
Page 19
2nd paragraph, both occurences of "Figure 1.10" should read "Figure 1.11"
Page 39
TABLE 2.4, see detailed description
Layer 2 destination MAC should be: "2222-2222-2222" Page 48
Step #5, should read "...P2, running only OSPF..."
Page 49
Under TDP, 4th line of router commands should read: see detailed description
Page 50
3rd line, Command should be "show tag-switching tdp neighbor"
10th line from bottom should read: P1(config)#interface serial 0/0
Page 92
Answer to Question #19 shoul be "B." The explanation is correct.
Page 99
Middle of page, "Peer LDP Ident: 192.168.1.1:0; Local TDP Ident" should read " Peer LDP Ident: 192.168.1.1:0; Local LDP Ident"
Page 166
Third line, "address family" should be "address-family"
Page 174
TABLE 5.6 Should look like:
Atlanta Customer A 1:1:10.1.0.0 /16
Atlanta Customer 1:2:10.1.0.0 /16
Raleigh Customer A 1:2:10.2.0.0 /16
Raleigh Customer 1:1:10.2.0.0 /16 Page 226-227
TABLEs 6.6 and 6.7 should be removed. FIGURE 2.7 on page 53 should take its place.
Page 228
6th line from top, vrf is already in the configuration. The ip vrf vpn_1 and associated configuration should not be there.
Page 286
Last line of page should read: ".........65000 subnets"
Page 314
Answer to Question 12, the explanation is confusing. for clarification:
If the down bit is set the routing bit is cleared.
A better answer is: Routing updates from a PE router to customer routers do not contain a routing bit. A routing bit is an internal mechanism on the PE. When a route is received on the PE router with the downbit the routing bit is cleared (meaning it will not show up in the routing table or be used). Page 318
Replace Fig. 8.1 with Fig. 7.19 (See Pg. 277).
Page 342
Replace Fig. 8.3 with Fig. 7.19 (See Pg. 277).
Page 352
Under Limiting Routes, 3rd & Last para., and the very last line, 'maximum-routes' should be "maximum routes"
Page 368
On vpn_a,vpn_b and vpn_c import routing target should be 1289:107. Also very last line should be "....1289:107"
Page 375
Ques. # 15 & 16, 'maximum-routes' should be "maximum routes"
Page 377
Ques. # 15 & 16 answers, 'maximum-routes' should be "maximum routes"
Page 401
Answer to Lab 5.2, Atlanta config should read: ip route vrf peer_vpn ....... for Raleigh it should read: ip route vrf peer_vpn .......
|
